Great Miter Saw Accessories. Reviews September, 2021, page 4

Fulton Precision Miter Gauge with Aluminum Miter Fence with 45 degree Angled Ends for Maximum Stock Support and a Repetitive Cut Flip Stop

Search only Fulton brand name
Fulton Precision Miter Gauge with Aluminum Miter Fence with 45 degree Angled Ends for Maximum Stock Support and a Repetitive Cut Flip Stop

Current price: 84.99 USD


Check price and availability


  • Both ends of the fence are cut at exactly 45 degrees. This allows you to position the fence extra close to the saw blade (with the power turned off) so you have even more control over the workpiece you are cutting. The fence comes with a flip stop that makes repetitive cuts a breeze. When not in use the flip stop can be flipped up and out of the way. Also include are two sticky back measuring tapes. 1 tape is left to right reading and the other is right to left reading.
  • Made from a single piece of extruded aluminum, this precision miter gauge fence is not only durable, its accurate and saves setup time. The fence is designed to be used with most any miter gauge with its off-set mounting track on the back of the fence. The off-set track allows you to flip the fence for lower profile miter gauge mounts and flip back for standard height miter gauges. The fence can be mounted to older miter gauges by adding a wooden block mount with wooden screws if necessary.
  • The head is mounted to a solid steel miter bar that measure 18” in length and is .354” thick by .730” wide. Standard miter slots are 3/4” x 3/8” with a 1/8” “T” slot (slight variances from brand to brand) running the length on the bottom of the slot. The steel miter bar is equipped with a metal, removable retaining disc that measures 7/8” in diameter and is just shy of 1/8” to fit into to the “T” slot to prevent accidental lifting when feeding your stock through.
  • The .200” thick, adjustable, solid aluminum head is machined with 13 positive stop holes. 1 hole is at 90 degrees while the 6 holes on both sides are at 22.5, 30, 45, 60, 67.5 and 90 degrees. The positive stops are perfect for many woodworking projects as they are the angles that are typically used.To adjust the head you simply loosen the post knob handle, pull the spring loaded indexing pin outward, rotate the head to the desired position, release the pin and lock into place.
  • The Fulton Miter Gauge is a high quality, well thought out and economical solution for your table saw cross cutting needs.The Aluminum Miter fence is equally well thought out with its 45 degree ends for unsurpassed workpiece support and its ability to mounted to most any miter gauge. Also included is a handy aluminum flip stop for repetitive angled cuts on your table saw. Together these three items are the perfect compliment to each other for your table saw cutting needs.

More Info

Milescraft 4009 FenceClamps- Universal,Silver

Search only Milescraft brand name
Milescraft 4009 FenceClamps- Universal,Silver

Current price: 10.96 USD


Check price and availability


Height: 1.45 Inches

Length: 5.5 Inches

Width: 5.5 Inches

Weight: 0.88 Pounds

Warranty: 2 year

  • Both ends of the fence are cut at exactly 45 degrees. This allows you to position the fence extra close to the saw blade (with the power turned off) so you have even more control over the workpiece you are cutting. The fence comes with a flip stop that makes repetitive cuts a breeze. When not in use the flip stop can be flipped up and out of the way. Also include are two sticky back measuring tapes. 1 tape is left to right reading and the other is right to left reading.
  • Made from a single piece of extruded aluminum, this precision miter gauge fence is not only durable, its accurate and saves setup time. The fence is designed to be used with most any miter gauge with its off-set mounting track on the back of the fence. The off-set track allows you to flip the fence for lower profile miter gauge mounts and flip back for standard height miter gauges. The fence can be mounted to older miter gauges by adding a wooden block mount with wooden screws if necessary.
  • The head is mounted to a solid steel miter bar that measure 18” in length and is .354” thick by .730” wide. Standard miter slots are 3/4” x 3/8” with a 1/8” “T” slot (slight variances from brand to brand) running the length on the bottom of the slot. The steel miter bar is equipped with a metal, removable retaining disc that measures 7/8” in diameter and is just shy of 1/8” to fit into to the “T” slot to prevent accidental lifting when feeding your stock through.
  • The .200” thick, adjustable, solid aluminum head is machined with 13 positive stop holes. 1 hole is at 90 degrees while the 6 holes on both sides are at 22.5, 30, 45, 60, 67.5 and 90 degrees. The positive stops are perfect for many woodworking projects as they are the angles that are typically used.To adjust the head you simply loosen the post knob handle, pull the spring loaded indexing pin outward, rotate the head to the desired position, release the pin and lock into place.
  • The Fulton Miter Gauge is a high quality, well thought out and economical solution for your table saw cross cutting needs.The Aluminum Miter fence is equally well thought out with its 45 degree ends for unsurpassed workpiece support and its ability to mounted to most any miter gauge. Also included is a handy aluminum flip stop for repetitive angled cuts on your table saw. Together these three items are the perfect compliment to each other for your table saw cutting needs.
  • Allow you to secure a wide variety of shop-made auxiliary fences to your existing fences without the Clamp getting in the way.
  • Range of travel 1/2″-5-3/4″ (12mm to 146mm)
  • Fits into a 3/8” hole in the top of the auxiliary fence

More Info

Fulton Precision Miter Gauge with a Standard Slot (3/4” x 3/8”) Steel Bar with Adjustable Spring Loaded Plungers and Removable Retaining Disc

Search only Fulton brand name
Fulton Precision Miter Gauge with a Standard Slot (3/4” x 3/8”) Steel Bar with Adjustable Spring Loaded Plungers and Removable Retaining Disc

Current price: 54.99 USD


Check price and availability


  • Both ends of the fence are cut at exactly 45 degrees. This allows you to position the fence extra close to the saw blade (with the power turned off) so you have even more control over the workpiece you are cutting. The fence comes with a flip stop that makes repetitive cuts a breeze. When not in use the flip stop can be flipped up and out of the way. Also include are two sticky back measuring tapes. 1 tape is left to right reading and the other is right to left reading.
  • Made from a single piece of extruded aluminum, this precision miter gauge fence is not only durable, its accurate and saves setup time. The fence is designed to be used with most any miter gauge with its off-set mounting track on the back of the fence. The off-set track allows you to flip the fence for lower profile miter gauge mounts and flip back for standard height miter gauges. The fence can be mounted to older miter gauges by adding a wooden block mount with wooden screws if necessary.
  • The head is mounted to a solid steel miter bar that measure 18” in length and is .354” thick by .730” wide. Standard miter slots are 3/4” x 3/8” with a 1/8” “T” slot (slight variances from brand to brand) running the length on the bottom of the slot. The steel miter bar is equipped with a metal, removable retaining disc that measures 7/8” in diameter and is just shy of 1/8” to fit into to the “T” slot to prevent accidental lifting when feeding your stock through.
  • The .200” thick, adjustable, solid aluminum head is machined with 13 positive stop holes. 1 hole is at 90 degrees while the 6 holes on both sides are at 22.5, 30, 45, 60, 67.5 and 90 degrees. The positive stops are perfect for many woodworking projects as they are the angles that are typically used.To adjust the head you simply loosen the post knob handle, pull the spring loaded indexing pin outward, rotate the head to the desired position, release the pin and lock into place.
  • The Fulton Miter Gauge is a high quality, well thought out and economical solution for your table saw cross cutting needs.The Aluminum Miter fence is equally well thought out with its 45 degree ends for unsurpassed workpiece support and its ability to mounted to most any miter gauge. Also included is a handy aluminum flip stop for repetitive angled cuts on your table saw. Together these three items are the perfect compliment to each other for your table saw cutting needs.
  • Allow you to secure a wide variety of shop-made auxiliary fences to your existing fences without the Clamp getting in the way.
  • Range of travel 1/2″-5-3/4″ (12mm to 146mm)
  • Fits into a 3/8” hole in the top of the auxiliary fence
  • The steel miter bar is equipped with a metal, removable retaining disc that measures 7/8” in diameter and is just shy of 1/8” to fit into to the “T” slot to prevent accidental lifting when feeding your stock through. If your saw does not have a “T” slot, you can remove the disc. The steel miter bar is also equipped with spring loaded, adjustable plungers on the side of the bar. The plungers can be adjusted with the provide hex key wrench in or out to provide you with the ideal fit.
  • The head is mounted to a solid steel miter bar that measure 18” in length and is .354” thick by .730” wide. Standard miter slots are 3/4” x 3/8” with a 1/8” “T” slot (slight variances from brand to brand) running the length on the bottom of the slot. The steel miter bar is equipped with a metal, removable retaining disc that measures 7/8” in diameter and is just shy of 1/8” to fit into to the “T” slot to prevent accidental lifting when feeding your stock through.
  • To adjust the head you simply loosen the post knob handle, pull the spring loaded indexing pin outward, rotate the head to the desired position, release the pin and lock into place by tightening the post knob handle. The aluminum head has two ¼” x ½” slots milled into it for mounting a miter fence if so desired. The slots are approximately 1-1/8” from the base of the miter gauge head.
  • The .200” thick, adjustable, solid aluminum head is machined with 13 positive stop holes. 1 hole is at 90 degrees while the 6 holes on both sides are at 22.5, 30, 45, 60, 67.5 and 90 degrees. The positive stops are perfect for many woodworking projects as they are the angles that are typically used.
  • If you own a table saw and you need to make a crosscut at any angle then you know how valuable a miter gauge can be. You may also know that the miter gauge that came with your saw is not terribly accurate or durable. Not to mention that the fit in the miter slot may not be all that great as well. The Fulton Miter Gauge is a high quality, well thought out and economical solution to your table saw cross cutting needs.

More Info

Sliding Compound Miter Saw, 10-Inch, 15 Amp, 2 Variable Speeds (4500 & 3200 RPM) with Bevel Cut (0-45°), 3 Blades (2 40T 1 48T), Laser Guide, Iron Blade Guard, Extension Table Included-EMS01A

Search only DSF brand name
Sliding Compound Miter Saw, 10-Inch, 15 Amp, 2 Variable Speeds (4500 & 3200 RPM) with Bevel Cut (0-45°), 3 Blades (2 40T 1 48T), Laser Guide, Iron Blade Guard, Extension Table Included-EMS01A

Current price: 144.97 USD

Saving: $95.02 (40%)


Check price and availability


Height: 13.779527545 Inches

Length: 30.708661386 Inches

Width: 18.897637776 Inches

Weight: 43 Pounds

  • Both ends of the fence are cut at exactly 45 degrees. This allows you to position the fence extra close to the saw blade (with the power turned off) so you have even more control over the workpiece you are cutting. The fence comes with a flip stop that makes repetitive cuts a breeze. When not in use the flip stop can be flipped up and out of the way. Also include are two sticky back measuring tapes. 1 tape is left to right reading and the other is right to left reading.
  • Made from a single piece of extruded aluminum, this precision miter gauge fence is not only durable, its accurate and saves setup time. The fence is designed to be used with most any miter gauge with its off-set mounting track on the back of the fence. The off-set track allows you to flip the fence for lower profile miter gauge mounts and flip back for standard height miter gauges. The fence can be mounted to older miter gauges by adding a wooden block mount with wooden screws if necessary.
  • The head is mounted to a solid steel miter bar that measure 18” in length and is .354” thick by .730” wide. Standard miter slots are 3/4” x 3/8” with a 1/8” “T” slot (slight variances from brand to brand) running the length on the bottom of the slot. The steel miter bar is equipped with a metal, removable retaining disc that measures 7/8” in diameter and is just shy of 1/8” to fit into to the “T” slot to prevent accidental lifting when feeding your stock through.
  • The .200” thick, adjustable, solid aluminum head is machined with 13 positive stop holes. 1 hole is at 90 degrees while the 6 holes on both sides are at 22.5, 30, 45, 60, 67.5 and 90 degrees. The positive stops are perfect for many woodworking projects as they are the angles that are typically used.To adjust the head you simply loosen the post knob handle, pull the spring loaded indexing pin outward, rotate the head to the desired position, release the pin and lock into place.
  • The Fulton Miter Gauge is a high quality, well thought out and economical solution for your table saw cross cutting needs.The Aluminum Miter fence is equally well thought out with its 45 degree ends for unsurpassed workpiece support and its ability to mounted to most any miter gauge. Also included is a handy aluminum flip stop for repetitive angled cuts on your table saw. Together these three items are the perfect compliment to each other for your table saw cutting needs.
  • Allow you to secure a wide variety of shop-made auxiliary fences to your existing fences without the Clamp getting in the way.
  • Range of travel 1/2″-5-3/4″ (12mm to 146mm)
  • Fits into a 3/8” hole in the top of the auxiliary fence
  • The steel miter bar is equipped with a metal, removable retaining disc that measures 7/8” in diameter and is just shy of 1/8” to fit into to the “T” slot to prevent accidental lifting when feeding your stock through. If your saw does not have a “T” slot, you can remove the disc. The steel miter bar is also equipped with spring loaded, adjustable plungers on the side of the bar. The plungers can be adjusted with the provide hex key wrench in or out to provide you with the ideal fit.
  • The head is mounted to a solid steel miter bar that measure 18” in length and is .354” thick by .730” wide. Standard miter slots are 3/4” x 3/8” with a 1/8” “T” slot (slight variances from brand to brand) running the length on the bottom of the slot. The steel miter bar is equipped with a metal, removable retaining disc that measures 7/8” in diameter and is just shy of 1/8” to fit into to the “T” slot to prevent accidental lifting when feeding your stock through.
  • To adjust the head you simply loosen the post knob handle, pull the spring loaded indexing pin outward, rotate the head to the desired position, release the pin and lock into place by tightening the post knob handle. The aluminum head has two ¼” x ½” slots milled into it for mounting a miter fence if so desired. The slots are approximately 1-1/8” from the base of the miter gauge head.
  • The .200” thick, adjustable, solid aluminum head is machined with 13 positive stop holes. 1 hole is at 90 degrees while the 6 holes on both sides are at 22.5, 30, 45, 60, 67.5 and 90 degrees. The positive stops are perfect for many woodworking projects as they are the angles that are typically used.
  • If you own a table saw and you need to make a crosscut at any angle then you know how valuable a miter gauge can be. You may also know that the miter gauge that came with your saw is not terribly accurate or durable. Not to mention that the fit in the miter slot may not be all that great as well. The Fulton Miter Gauge is a high quality, well thought out and economical solution to your table saw cross cutting needs.
  • 【Package Contents & 2-year Warranty】- advanced 10-inch 15-amp miter saw,1*10" multi-function blade, 2*10" blades for wood, 1* dust bag, 2*hexagonal wrench, 2* clamping device, 1*User Manual, 1*Warranty Card, 24 Months Warranty.
  • 【Clean Environment & Extension Table】- Additional chip bag connects directly to the saw,and helps to collect sawdust away from the workpiece during cutting. 35mm dust port allows you to connect your vacuum cleaner with an adapter instead of a bag to capture more of the dust. Extension table with vice clamping provides better support and balance, adding stability when cutting.
  • 【3 Blades & Iron Blade Guard】- Richer accessories provide a wide range of choices, two 10" 40T TCT blades for wood and plastic, and one multifunctional 10" 48T TCT blade for versatile use. Solid iron Self-retracting saw shield covers the teeth of the cutting blade, helps protect from accidental mishaps.
  • 【Bevel Cutting & Laser Guide】- A free bevel range from 0°to 45° allows you to make beveled cuts for more versatile uses. And the angle of the miter bench is -45°/0°/+45°with positive stops at 0°, 15°, 22.5°, 30°, and 45° in both directions. Comes with a laser that accurately tracks the real-time position and allows you to make precise adjustments.
  • 【2 Speed & Durable Tool】- With the single press of the switch, you can convert between two speeds(3200 RPM or 4500 RPM) with ease for more precise cutting, high speed for wood while low speed for metal. The sliding cutting design allows for cutting longer boards. Built from stainless steel castings, it provides you with a solid saw that is able to withstand the daily rigors that come with working on a job site.

More Info

NXPOXS Replacement DW7084 Crown Moulding Stop for DEWALT Miter Saw DW703, DW706, DW708, DW712, DW715, DW716, DW717, DW718

Search only NXPOXS brand name
NXPOXS Replacement DW7084 Crown Moulding Stop for DEWALT Miter Saw DW703, DW706, DW708, DW712, DW715, DW716, DW717, DW718

Current price: 13.99 USD


Check price and availability


  • Both ends of the fence are cut at exactly 45 degrees. This allows you to position the fence extra close to the saw blade (with the power turned off) so you have even more control over the workpiece you are cutting. The fence comes with a flip stop that makes repetitive cuts a breeze. When not in use the flip stop can be flipped up and out of the way. Also include are two sticky back measuring tapes. 1 tape is left to right reading and the other is right to left reading.
  • Made from a single piece of extruded aluminum, this precision miter gauge fence is not only durable, its accurate and saves setup time. The fence is designed to be used with most any miter gauge with its off-set mounting track on the back of the fence. The off-set track allows you to flip the fence for lower profile miter gauge mounts and flip back for standard height miter gauges. The fence can be mounted to older miter gauges by adding a wooden block mount with wooden screws if necessary.
  • The head is mounted to a solid steel miter bar that measure 18” in length and is .354” thick by .730” wide. Standard miter slots are 3/4” x 3/8” with a 1/8” “T” slot (slight variances from brand to brand) running the length on the bottom of the slot. The steel miter bar is equipped with a metal, removable retaining disc that measures 7/8” in diameter and is just shy of 1/8” to fit into to the “T” slot to prevent accidental lifting when feeding your stock through.
  • The .200” thick, adjustable, solid aluminum head is machined with 13 positive stop holes. 1 hole is at 90 degrees while the 6 holes on both sides are at 22.5, 30, 45, 60, 67.5 and 90 degrees. The positive stops are perfect for many woodworking projects as they are the angles that are typically used.To adjust the head you simply loosen the post knob handle, pull the spring loaded indexing pin outward, rotate the head to the desired position, release the pin and lock into place.
  • The Fulton Miter Gauge is a high quality, well thought out and economical solution for your table saw cross cutting needs.The Aluminum Miter fence is equally well thought out with its 45 degree ends for unsurpassed workpiece support and its ability to mounted to most any miter gauge. Also included is a handy aluminum flip stop for repetitive angled cuts on your table saw. Together these three items are the perfect compliment to each other for your table saw cutting needs.
  • Allow you to secure a wide variety of shop-made auxiliary fences to your existing fences without the Clamp getting in the way.
  • Range of travel 1/2″-5-3/4″ (12mm to 146mm)
  • Fits into a 3/8” hole in the top of the auxiliary fence
  • The steel miter bar is equipped with a metal, removable retaining disc that measures 7/8” in diameter and is just shy of 1/8” to fit into to the “T” slot to prevent accidental lifting when feeding your stock through. If your saw does not have a “T” slot, you can remove the disc. The steel miter bar is also equipped with spring loaded, adjustable plungers on the side of the bar. The plungers can be adjusted with the provide hex key wrench in or out to provide you with the ideal fit.
  • The head is mounted to a solid steel miter bar that measure 18” in length and is .354” thick by .730” wide. Standard miter slots are 3/4” x 3/8” with a 1/8” “T” slot (slight variances from brand to brand) running the length on the bottom of the slot. The steel miter bar is equipped with a metal, removable retaining disc that measures 7/8” in diameter and is just shy of 1/8” to fit into to the “T” slot to prevent accidental lifting when feeding your stock through.
  • To adjust the head you simply loosen the post knob handle, pull the spring loaded indexing pin outward, rotate the head to the desired position, release the pin and lock into place by tightening the post knob handle. The aluminum head has two ¼” x ½” slots milled into it for mounting a miter fence if so desired. The slots are approximately 1-1/8” from the base of the miter gauge head.
  • The .200” thick, adjustable, solid aluminum head is machined with 13 positive stop holes. 1 hole is at 90 degrees while the 6 holes on both sides are at 22.5, 30, 45, 60, 67.5 and 90 degrees. The positive stops are perfect for many woodworking projects as they are the angles that are typically used.
  • If you own a table saw and you need to make a crosscut at any angle then you know how valuable a miter gauge can be. You may also know that the miter gauge that came with your saw is not terribly accurate or durable. Not to mention that the fit in the miter slot may not be all that great as well. The Fulton Miter Gauge is a high quality, well thought out and economical solution to your table saw cross cutting needs.
  • 【Package Contents & 2-year Warranty】- advanced 10-inch 15-amp miter saw,1*10" multi-function blade, 2*10" blades for wood, 1* dust bag, 2*hexagonal wrench, 2* clamping device, 1*User Manual, 1*Warranty Card, 24 Months Warranty.
  • 【Clean Environment & Extension Table】- Additional chip bag connects directly to the saw,and helps to collect sawdust away from the workpiece during cutting. 35mm dust port allows you to connect your vacuum cleaner with an adapter instead of a bag to capture more of the dust. Extension table with vice clamping provides better support and balance, adding stability when cutting.
  • 【3 Blades & Iron Blade Guard】- Richer accessories provide a wide range of choices, two 10" 40T TCT blades for wood and plastic, and one multifunctional 10" 48T TCT blade for versatile use. Solid iron Self-retracting saw shield covers the teeth of the cutting blade, helps protect from accidental mishaps.
  • 【Bevel Cutting & Laser Guide】- A free bevel range from 0°to 45° allows you to make beveled cuts for more versatile uses. And the angle of the miter bench is -45°/0°/+45°with positive stops at 0°, 15°, 22.5°, 30°, and 45° in both directions. Comes with a laser that accurately tracks the real-time position and allows you to make precise adjustments.
  • 【2 Speed & Durable Tool】- With the single press of the switch, you can convert between two speeds(3200 RPM or 4500 RPM) with ease for more precise cutting, high speed for wood while low speed for metal. The sliding cutting design allows for cutting longer boards. Built from stainless steel castings, it provides you with a solid saw that is able to withstand the daily rigors that come with working on a job site.
  • These crown stops accurately position crown molding vertically against the saw fence.
  • Measures 6-1/2-x-4-1/2 inches.
  • Package include: 2 crown stops,one for each side of the blade, 2 screw knob, 2 nut clips.
  • Easy to adjust, strong and ridged. Replace for DEWALT DW7084.
  • These replacement Crown Stops are designed to fit for DeWalt miter saw DWS779 DWS780 DW703, DW706, DW708, DW712, DW715, DW716, DW717, DW718

More Info

ZEROPLAY Miter Bars by MICROJIG (Double Pack)

Search only MICRO JIG brand name
ZEROPLAY Miter Bars by MICROJIG (Double Pack)

Current price: 34 USD


Check price and availability


Height: 1 Inches

Length: 10 Inches

Width: 1 Inches

Weight: 0.26 Pounds

Warranty: Extended 3-Year Warranty from Authorized Resellers

  • Both ends of the fence are cut at exactly 45 degrees. This allows you to position the fence extra close to the saw blade (with the power turned off) so you have even more control over the workpiece you are cutting. The fence comes with a flip stop that makes repetitive cuts a breeze. When not in use the flip stop can be flipped up and out of the way. Also include are two sticky back measuring tapes. 1 tape is left to right reading and the other is right to left reading.
  • Made from a single piece of extruded aluminum, this precision miter gauge fence is not only durable, its accurate and saves setup time. The fence is designed to be used with most any miter gauge with its off-set mounting track on the back of the fence. The off-set track allows you to flip the fence for lower profile miter gauge mounts and flip back for standard height miter gauges. The fence can be mounted to older miter gauges by adding a wooden block mount with wooden screws if necessary.
  • The head is mounted to a solid steel miter bar that measure 18” in length and is .354” thick by .730” wide. Standard miter slots are 3/4” x 3/8” with a 1/8” “T” slot (slight variances from brand to brand) running the length on the bottom of the slot. The steel miter bar is equipped with a metal, removable retaining disc that measures 7/8” in diameter and is just shy of 1/8” to fit into to the “T” slot to prevent accidental lifting when feeding your stock through.
  • The .200” thick, adjustable, solid aluminum head is machined with 13 positive stop holes. 1 hole is at 90 degrees while the 6 holes on both sides are at 22.5, 30, 45, 60, 67.5 and 90 degrees. The positive stops are perfect for many woodworking projects as they are the angles that are typically used.To adjust the head you simply loosen the post knob handle, pull the spring loaded indexing pin outward, rotate the head to the desired position, release the pin and lock into place.
  • The Fulton Miter Gauge is a high quality, well thought out and economical solution for your table saw cross cutting needs.The Aluminum Miter fence is equally well thought out with its 45 degree ends for unsurpassed workpiece support and its ability to mounted to most any miter gauge. Also included is a handy aluminum flip stop for repetitive angled cuts on your table saw. Together these three items are the perfect compliment to each other for your table saw cutting needs.
  • Allow you to secure a wide variety of shop-made auxiliary fences to your existing fences without the Clamp getting in the way.
  • Range of travel 1/2″-5-3/4″ (12mm to 146mm)
  • Fits into a 3/8” hole in the top of the auxiliary fence
  • The steel miter bar is equipped with a metal, removable retaining disc that measures 7/8” in diameter and is just shy of 1/8” to fit into to the “T” slot to prevent accidental lifting when feeding your stock through. If your saw does not have a “T” slot, you can remove the disc. The steel miter bar is also equipped with spring loaded, adjustable plungers on the side of the bar. The plungers can be adjusted with the provide hex key wrench in or out to provide you with the ideal fit.
  • The head is mounted to a solid steel miter bar that measure 18” in length and is .354” thick by .730” wide. Standard miter slots are 3/4” x 3/8” with a 1/8” “T” slot (slight variances from brand to brand) running the length on the bottom of the slot. The steel miter bar is equipped with a metal, removable retaining disc that measures 7/8” in diameter and is just shy of 1/8” to fit into to the “T” slot to prevent accidental lifting when feeding your stock through.
  • To adjust the head you simply loosen the post knob handle, pull the spring loaded indexing pin outward, rotate the head to the desired position, release the pin and lock into place by tightening the post knob handle. The aluminum head has two ¼” x ½” slots milled into it for mounting a miter fence if so desired. The slots are approximately 1-1/8” from the base of the miter gauge head.
  • The .200” thick, adjustable, solid aluminum head is machined with 13 positive stop holes. 1 hole is at 90 degrees while the 6 holes on both sides are at 22.5, 30, 45, 60, 67.5 and 90 degrees. The positive stops are perfect for many woodworking projects as they are the angles that are typically used.
  • If you own a table saw and you need to make a crosscut at any angle then you know how valuable a miter gauge can be. You may also know that the miter gauge that came with your saw is not terribly accurate or durable. Not to mention that the fit in the miter slot may not be all that great as well. The Fulton Miter Gauge is a high quality, well thought out and economical solution to your table saw cross cutting needs.
  • 【Package Contents & 2-year Warranty】- advanced 10-inch 15-amp miter saw,1*10" multi-function blade, 2*10" blades for wood, 1* dust bag, 2*hexagonal wrench, 2* clamping device, 1*User Manual, 1*Warranty Card, 24 Months Warranty.
  • 【Clean Environment & Extension Table】- Additional chip bag connects directly to the saw,and helps to collect sawdust away from the workpiece during cutting. 35mm dust port allows you to connect your vacuum cleaner with an adapter instead of a bag to capture more of the dust. Extension table with vice clamping provides better support and balance, adding stability when cutting.
  • 【3 Blades & Iron Blade Guard】- Richer accessories provide a wide range of choices, two 10" 40T TCT blades for wood and plastic, and one multifunctional 10" 48T TCT blade for versatile use. Solid iron Self-retracting saw shield covers the teeth of the cutting blade, helps protect from accidental mishaps.
  • 【Bevel Cutting & Laser Guide】- A free bevel range from 0°to 45° allows you to make beveled cuts for more versatile uses. And the angle of the miter bench is -45°/0°/+45°with positive stops at 0°, 15°, 22.5°, 30°, and 45° in both directions. Comes with a laser that accurately tracks the real-time position and allows you to make precise adjustments.
  • 【2 Speed & Durable Tool】- With the single press of the switch, you can convert between two speeds(3200 RPM or 4500 RPM) with ease for more precise cutting, high speed for wood while low speed for metal. The sliding cutting design allows for cutting longer boards. Built from stainless steel castings, it provides you with a solid saw that is able to withstand the daily rigors that come with working on a job site.
  • These crown stops accurately position crown molding vertically against the saw fence.
  • Measures 6-1/2-x-4-1/2 inches.
  • Package include: 2 crown stops,one for each side of the blade, 2 screw knob, 2 nut clips.
  • Easy to adjust, strong and ridged. Replace for DEWALT DW7084.
  • These replacement Crown Stops are designed to fit for DeWalt miter saw DWS779 DWS780 DW703, DW706, DW708, DW712, DW715, DW716, DW717, DW718
  • Made in the USA
  • ZEROPLAY Miter Bars will fit ANY standard (3/4” x 3/8”) T-Track miter slot that measures between 0. 73" and 0. 79" wide and at least 5/16" deep
  • Top-down installation for easy and fast mounting to jigs, fixtures and sleds
  • No slop, side-to-side play or seasonal warping
  • Build table saw sleds fast

More Info

RYOBI OEM 204443001 Assembly DUST Bag in Genuine Factory Package

Search only RYOBI brand name
RYOBI OEM 204443001 Assembly DUST Bag in Genuine Factory Package

Current price: 9.9 USD

Saving: $3.24 (25%)


Check price and availability


Height: 1.8 Inches

Length: 6.5 Inches

Width: 1.8 Inches

  • Both ends of the fence are cut at exactly 45 degrees. This allows you to position the fence extra close to the saw blade (with the power turned off) so you have even more control over the workpiece you are cutting. The fence comes with a flip stop that makes repetitive cuts a breeze. When not in use the flip stop can be flipped up and out of the way. Also include are two sticky back measuring tapes. 1 tape is left to right reading and the other is right to left reading.
  • Made from a single piece of extruded aluminum, this precision miter gauge fence is not only durable, its accurate and saves setup time. The fence is designed to be used with most any miter gauge with its off-set mounting track on the back of the fence. The off-set track allows you to flip the fence for lower profile miter gauge mounts and flip back for standard height miter gauges. The fence can be mounted to older miter gauges by adding a wooden block mount with wooden screws if necessary.
  • The head is mounted to a solid steel miter bar that measure 18” in length and is .354” thick by .730” wide. Standard miter slots are 3/4” x 3/8” with a 1/8” “T” slot (slight variances from brand to brand) running the length on the bottom of the slot. The steel miter bar is equipped with a metal, removable retaining disc that measures 7/8” in diameter and is just shy of 1/8” to fit into to the “T” slot to prevent accidental lifting when feeding your stock through.
  • The .200” thick, adjustable, solid aluminum head is machined with 13 positive stop holes. 1 hole is at 90 degrees while the 6 holes on both sides are at 22.5, 30, 45, 60, 67.5 and 90 degrees. The positive stops are perfect for many woodworking projects as they are the angles that are typically used.To adjust the head you simply loosen the post knob handle, pull the spring loaded indexing pin outward, rotate the head to the desired position, release the pin and lock into place.
  • The Fulton Miter Gauge is a high quality, well thought out and economical solution for your table saw cross cutting needs.The Aluminum Miter fence is equally well thought out with its 45 degree ends for unsurpassed workpiece support and its ability to mounted to most any miter gauge. Also included is a handy aluminum flip stop for repetitive angled cuts on your table saw. Together these three items are the perfect compliment to each other for your table saw cutting needs.
  • Allow you to secure a wide variety of shop-made auxiliary fences to your existing fences without the Clamp getting in the way.
  • Range of travel 1/2″-5-3/4″ (12mm to 146mm)
  • Fits into a 3/8” hole in the top of the auxiliary fence
  • The steel miter bar is equipped with a metal, removable retaining disc that measures 7/8” in diameter and is just shy of 1/8” to fit into to the “T” slot to prevent accidental lifting when feeding your stock through. If your saw does not have a “T” slot, you can remove the disc. The steel miter bar is also equipped with spring loaded, adjustable plungers on the side of the bar. The plungers can be adjusted with the provide hex key wrench in or out to provide you with the ideal fit.
  • The head is mounted to a solid steel miter bar that measure 18” in length and is .354” thick by .730” wide. Standard miter slots are 3/4” x 3/8” with a 1/8” “T” slot (slight variances from brand to brand) running the length on the bottom of the slot. The steel miter bar is equipped with a metal, removable retaining disc that measures 7/8” in diameter and is just shy of 1/8” to fit into to the “T” slot to prevent accidental lifting when feeding your stock through.
  • To adjust the head you simply loosen the post knob handle, pull the spring loaded indexing pin outward, rotate the head to the desired position, release the pin and lock into place by tightening the post knob handle. The aluminum head has two ¼” x ½” slots milled into it for mounting a miter fence if so desired. The slots are approximately 1-1/8” from the base of the miter gauge head.
  • The .200” thick, adjustable, solid aluminum head is machined with 13 positive stop holes. 1 hole is at 90 degrees while the 6 holes on both sides are at 22.5, 30, 45, 60, 67.5 and 90 degrees. The positive stops are perfect for many woodworking projects as they are the angles that are typically used.
  • If you own a table saw and you need to make a crosscut at any angle then you know how valuable a miter gauge can be. You may also know that the miter gauge that came with your saw is not terribly accurate or durable. Not to mention that the fit in the miter slot may not be all that great as well. The Fulton Miter Gauge is a high quality, well thought out and economical solution to your table saw cross cutting needs.
  • 【Package Contents & 2-year Warranty】- advanced 10-inch 15-amp miter saw,1*10" multi-function blade, 2*10" blades for wood, 1* dust bag, 2*hexagonal wrench, 2* clamping device, 1*User Manual, 1*Warranty Card, 24 Months Warranty.
  • 【Clean Environment & Extension Table】- Additional chip bag connects directly to the saw,and helps to collect sawdust away from the workpiece during cutting. 35mm dust port allows you to connect your vacuum cleaner with an adapter instead of a bag to capture more of the dust. Extension table with vice clamping provides better support and balance, adding stability when cutting.
  • 【3 Blades & Iron Blade Guard】- Richer accessories provide a wide range of choices, two 10" 40T TCT blades for wood and plastic, and one multifunctional 10" 48T TCT blade for versatile use. Solid iron Self-retracting saw shield covers the teeth of the cutting blade, helps protect from accidental mishaps.
  • 【Bevel Cutting & Laser Guide】- A free bevel range from 0°to 45° allows you to make beveled cuts for more versatile uses. And the angle of the miter bench is -45°/0°/+45°with positive stops at 0°, 15°, 22.5°, 30°, and 45° in both directions. Comes with a laser that accurately tracks the real-time position and allows you to make precise adjustments.
  • 【2 Speed & Durable Tool】- With the single press of the switch, you can convert between two speeds(3200 RPM or 4500 RPM) with ease for more precise cutting, high speed for wood while low speed for metal. The sliding cutting design allows for cutting longer boards. Built from stainless steel castings, it provides you with a solid saw that is able to withstand the daily rigors that come with working on a job site.
  • These crown stops accurately position crown molding vertically against the saw fence.
  • Measures 6-1/2-x-4-1/2 inches.
  • Package include: 2 crown stops,one for each side of the blade, 2 screw knob, 2 nut clips.
  • Easy to adjust, strong and ridged. Replace for DEWALT DW7084.
  • These replacement Crown Stops are designed to fit for DeWalt miter saw DWS779 DWS780 DW703, DW706, DW708, DW712, DW715, DW716, DW717, DW718
  • Made in the USA
  • ZEROPLAY Miter Bars will fit ANY standard (3/4” x 3/8”) T-Track miter slot that measures between 0. 73" and 0. 79" wide and at least 5/16" deep
  • Top-down installation for easy and fast mounting to jigs, fixtures and sleds
  • No slop, side-to-side play or seasonal warping
  • Build table saw sleds fast
  • Compatible with: P450
  • Ryobi replacement assembly dust bag, part number 204443001
  • Genuine, OEM Ryobi Replacement Part
  • Please Note: Does not fit all specs of above models listed, please consult owner's manual for proper part number identification and proper installation
  • Compatible with: Specific P450 18v Brushless Belt Sanders

More Info

Miter Saw Protractor, Professional Miter Saw Protractor Angle Finder Replaces the Model #505P-7 Miter Saw Protractor with Measuring Rulers for Angle Finder Carpentry, Crown Molding Tool, Baseboard

Search only LUVRD brand name
Miter Saw Protractor, Professional Miter Saw Protractor Angle Finder Replaces the Model #505P-7 Miter Saw Protractor with Measuring Rulers for Angle Finder Carpentry, Crown Molding Tool, Baseboard

Current price: 14.69 USD


Check price and availability


  • Both ends of the fence are cut at exactly 45 degrees. This allows you to position the fence extra close to the saw blade (with the power turned off) so you have even more control over the workpiece you are cutting. The fence comes with a flip stop that makes repetitive cuts a breeze. When not in use the flip stop can be flipped up and out of the way. Also include are two sticky back measuring tapes. 1 tape is left to right reading and the other is right to left reading.
  • Made from a single piece of extruded aluminum, this precision miter gauge fence is not only durable, its accurate and saves setup time. The fence is designed to be used with most any miter gauge with its off-set mounting track on the back of the fence. The off-set track allows you to flip the fence for lower profile miter gauge mounts and flip back for standard height miter gauges. The fence can be mounted to older miter gauges by adding a wooden block mount with wooden screws if necessary.
  • The head is mounted to a solid steel miter bar that measure 18” in length and is .354” thick by .730” wide. Standard miter slots are 3/4” x 3/8” with a 1/8” “T” slot (slight variances from brand to brand) running the length on the bottom of the slot. The steel miter bar is equipped with a metal, removable retaining disc that measures 7/8” in diameter and is just shy of 1/8” to fit into to the “T” slot to prevent accidental lifting when feeding your stock through.
  • The .200” thick, adjustable, solid aluminum head is machined with 13 positive stop holes. 1 hole is at 90 degrees while the 6 holes on both sides are at 22.5, 30, 45, 60, 67.5 and 90 degrees. The positive stops are perfect for many woodworking projects as they are the angles that are typically used.To adjust the head you simply loosen the post knob handle, pull the spring loaded indexing pin outward, rotate the head to the desired position, release the pin and lock into place.
  • The Fulton Miter Gauge is a high quality, well thought out and economical solution for your table saw cross cutting needs.The Aluminum Miter fence is equally well thought out with its 45 degree ends for unsurpassed workpiece support and its ability to mounted to most any miter gauge. Also included is a handy aluminum flip stop for repetitive angled cuts on your table saw. Together these three items are the perfect compliment to each other for your table saw cutting needs.
  • Allow you to secure a wide variety of shop-made auxiliary fences to your existing fences without the Clamp getting in the way.
  • Range of travel 1/2″-5-3/4″ (12mm to 146mm)
  • Fits into a 3/8” hole in the top of the auxiliary fence
  • The steel miter bar is equipped with a metal, removable retaining disc that measures 7/8” in diameter and is just shy of 1/8” to fit into to the “T” slot to prevent accidental lifting when feeding your stock through. If your saw does not have a “T” slot, you can remove the disc. The steel miter bar is also equipped with spring loaded, adjustable plungers on the side of the bar. The plungers can be adjusted with the provide hex key wrench in or out to provide you with the ideal fit.
  • The head is mounted to a solid steel miter bar that measure 18” in length and is .354” thick by .730” wide. Standard miter slots are 3/4” x 3/8” with a 1/8” “T” slot (slight variances from brand to brand) running the length on the bottom of the slot. The steel miter bar is equipped with a metal, removable retaining disc that measures 7/8” in diameter and is just shy of 1/8” to fit into to the “T” slot to prevent accidental lifting when feeding your stock through.
  • To adjust the head you simply loosen the post knob handle, pull the spring loaded indexing pin outward, rotate the head to the desired position, release the pin and lock into place by tightening the post knob handle. The aluminum head has two ¼” x ½” slots milled into it for mounting a miter fence if so desired. The slots are approximately 1-1/8” from the base of the miter gauge head.
  • The .200” thick, adjustable, solid aluminum head is machined with 13 positive stop holes. 1 hole is at 90 degrees while the 6 holes on both sides are at 22.5, 30, 45, 60, 67.5 and 90 degrees. The positive stops are perfect for many woodworking projects as they are the angles that are typically used.
  • If you own a table saw and you need to make a crosscut at any angle then you know how valuable a miter gauge can be. You may also know that the miter gauge that came with your saw is not terribly accurate or durable. Not to mention that the fit in the miter slot may not be all that great as well. The Fulton Miter Gauge is a high quality, well thought out and economical solution to your table saw cross cutting needs.
  • 【Package Contents & 2-year Warranty】- advanced 10-inch 15-amp miter saw,1*10" multi-function blade, 2*10" blades for wood, 1* dust bag, 2*hexagonal wrench, 2* clamping device, 1*User Manual, 1*Warranty Card, 24 Months Warranty.
  • 【Clean Environment & Extension Table】- Additional chip bag connects directly to the saw,and helps to collect sawdust away from the workpiece during cutting. 35mm dust port allows you to connect your vacuum cleaner with an adapter instead of a bag to capture more of the dust. Extension table with vice clamping provides better support and balance, adding stability when cutting.
  • 【3 Blades & Iron Blade Guard】- Richer accessories provide a wide range of choices, two 10" 40T TCT blades for wood and plastic, and one multifunctional 10" 48T TCT blade for versatile use. Solid iron Self-retracting saw shield covers the teeth of the cutting blade, helps protect from accidental mishaps.
  • 【Bevel Cutting & Laser Guide】- A free bevel range from 0°to 45° allows you to make beveled cuts for more versatile uses. And the angle of the miter bench is -45°/0°/+45°with positive stops at 0°, 15°, 22.5°, 30°, and 45° in both directions. Comes with a laser that accurately tracks the real-time position and allows you to make precise adjustments.
  • 【2 Speed & Durable Tool】- With the single press of the switch, you can convert between two speeds(3200 RPM or 4500 RPM) with ease for more precise cutting, high speed for wood while low speed for metal. The sliding cutting design allows for cutting longer boards. Built from stainless steel castings, it provides you with a solid saw that is able to withstand the daily rigors that come with working on a job site.
  • These crown stops accurately position crown molding vertically against the saw fence.
  • Measures 6-1/2-x-4-1/2 inches.
  • Package include: 2 crown stops,one for each side of the blade, 2 screw knob, 2 nut clips.
  • Easy to adjust, strong and ridged. Replace for DEWALT DW7084.
  • These replacement Crown Stops are designed to fit for DeWalt miter saw DWS779 DWS780 DW703, DW706, DW708, DW712, DW715, DW716, DW717, DW718
  • Made in the USA
  • ZEROPLAY Miter Bars will fit ANY standard (3/4” x 3/8”) T-Track miter slot that measures between 0. 73" and 0. 79" wide and at least 5/16" deep
  • Top-down installation for easy and fast mounting to jigs, fixtures and sleds
  • No slop, side-to-side play or seasonal warping
  • Build table saw sleds fast
  • Compatible with: P450
  • Ryobi replacement assembly dust bag, part number 204443001
  • Genuine, OEM Ryobi Replacement Part
  • Please Note: Does not fit all specs of above models listed, please consult owner's manual for proper part number identification and proper installation
  • Compatible with: Specific P450 18v Brushless Belt Sanders
  • UNCONDITIONAL WARRANTY - LUVRD focuses on construction accessories, and we stand by our carpenter protractor, brings better alternatives for you in the miter saw protractor for woodworking. Welcome to find us with any product-related queries on buyer message
  • EASY TO USE - Owing to the adjustable and collapsible design, not only is this miter saw protractor angle finder easy to use, but also convenient to carry or store and feature a one-handed operation with a unique tightening mechanism
  • SUPERIOR QUALITY AND DURABILITY - This trig crown molding jig angle finder is durable and stronger than other pvc plastic miter angle gauge because it is made of high-quality ABS. Moreover, The miter saw protractor is resistant to scratch for daily use
  • FRIENDLY DESIGN - LUVRD professional miter saw protractor is not only an excellent replacement for 505p-7 miter saw protractor angle finder corner crown molding tool, but also a measuring rule in inches for construction
  • PRECISE MEASUREMENT - This miter saw protractor angle finder is specifically designed to ensure a correct and precise miter angle finder with no effort. The miter saw protractor could provide you the exact angle you need (inside or outside corners) to make your perfect trim for crown molding tool, baseboard molding and more

More Info

POWERTEC 70122 Big Gulp Dust Hood

Search only POWERTEC brand name
POWERTEC 70122 Big Gulp Dust Hood

Current price: 19.62 USD


Check price and availability


Height: 10.5 Inches

Length: 16 Inches

Width: 13 Inches

Weight: 1.2 Pounds

  • Both ends of the fence are cut at exactly 45 degrees. This allows you to position the fence extra close to the saw blade (with the power turned off) so you have even more control over the workpiece you are cutting. The fence comes with a flip stop that makes repetitive cuts a breeze. When not in use the flip stop can be flipped up and out of the way. Also include are two sticky back measuring tapes. 1 tape is left to right reading and the other is right to left reading.
  • Made from a single piece of extruded aluminum, this precision miter gauge fence is not only durable, its accurate and saves setup time. The fence is designed to be used with most any miter gauge with its off-set mounting track on the back of the fence. The off-set track allows you to flip the fence for lower profile miter gauge mounts and flip back for standard height miter gauges. The fence can be mounted to older miter gauges by adding a wooden block mount with wooden screws if necessary.
  • The head is mounted to a solid steel miter bar that measure 18” in length and is .354” thick by .730” wide. Standard miter slots are 3/4” x 3/8” with a 1/8” “T” slot (slight variances from brand to brand) running the length on the bottom of the slot. The steel miter bar is equipped with a metal, removable retaining disc that measures 7/8” in diameter and is just shy of 1/8” to fit into to the “T” slot to prevent accidental lifting when feeding your stock through.
  • The .200” thick, adjustable, solid aluminum head is machined with 13 positive stop holes. 1 hole is at 90 degrees while the 6 holes on both sides are at 22.5, 30, 45, 60, 67.5 and 90 degrees. The positive stops are perfect for many woodworking projects as they are the angles that are typically used.To adjust the head you simply loosen the post knob handle, pull the spring loaded indexing pin outward, rotate the head to the desired position, release the pin and lock into place.
  • The Fulton Miter Gauge is a high quality, well thought out and economical solution for your table saw cross cutting needs.The Aluminum Miter fence is equally well thought out with its 45 degree ends for unsurpassed workpiece support and its ability to mounted to most any miter gauge. Also included is a handy aluminum flip stop for repetitive angled cuts on your table saw. Together these three items are the perfect compliment to each other for your table saw cutting needs.
  • Allow you to secure a wide variety of shop-made auxiliary fences to your existing fences without the Clamp getting in the way.
  • Range of travel 1/2″-5-3/4″ (12mm to 146mm)
  • Fits into a 3/8” hole in the top of the auxiliary fence
  • The steel miter bar is equipped with a metal, removable retaining disc that measures 7/8” in diameter and is just shy of 1/8” to fit into to the “T” slot to prevent accidental lifting when feeding your stock through. If your saw does not have a “T” slot, you can remove the disc. The steel miter bar is also equipped with spring loaded, adjustable plungers on the side of the bar. The plungers can be adjusted with the provide hex key wrench in or out to provide you with the ideal fit.
  • The head is mounted to a solid steel miter bar that measure 18” in length and is .354” thick by .730” wide. Standard miter slots are 3/4” x 3/8” with a 1/8” “T” slot (slight variances from brand to brand) running the length on the bottom of the slot. The steel miter bar is equipped with a metal, removable retaining disc that measures 7/8” in diameter and is just shy of 1/8” to fit into to the “T” slot to prevent accidental lifting when feeding your stock through.
  • To adjust the head you simply loosen the post knob handle, pull the spring loaded indexing pin outward, rotate the head to the desired position, release the pin and lock into place by tightening the post knob handle. The aluminum head has two ¼” x ½” slots milled into it for mounting a miter fence if so desired. The slots are approximately 1-1/8” from the base of the miter gauge head.
  • The .200” thick, adjustable, solid aluminum head is machined with 13 positive stop holes. 1 hole is at 90 degrees while the 6 holes on both sides are at 22.5, 30, 45, 60, 67.5 and 90 degrees. The positive stops are perfect for many woodworking projects as they are the angles that are typically used.
  • If you own a table saw and you need to make a crosscut at any angle then you know how valuable a miter gauge can be. You may also know that the miter gauge that came with your saw is not terribly accurate or durable. Not to mention that the fit in the miter slot may not be all that great as well. The Fulton Miter Gauge is a high quality, well thought out and economical solution to your table saw cross cutting needs.
  • 【Package Contents & 2-year Warranty】- advanced 10-inch 15-amp miter saw,1*10" multi-function blade, 2*10" blades for wood, 1* dust bag, 2*hexagonal wrench, 2* clamping device, 1*User Manual, 1*Warranty Card, 24 Months Warranty.
  • 【Clean Environment & Extension Table】- Additional chip bag connects directly to the saw,and helps to collect sawdust away from the workpiece during cutting. 35mm dust port allows you to connect your vacuum cleaner with an adapter instead of a bag to capture more of the dust. Extension table with vice clamping provides better support and balance, adding stability when cutting.
  • 【3 Blades & Iron Blade Guard】- Richer accessories provide a wide range of choices, two 10" 40T TCT blades for wood and plastic, and one multifunctional 10" 48T TCT blade for versatile use. Solid iron Self-retracting saw shield covers the teeth of the cutting blade, helps protect from accidental mishaps.
  • 【Bevel Cutting & Laser Guide】- A free bevel range from 0°to 45° allows you to make beveled cuts for more versatile uses. And the angle of the miter bench is -45°/0°/+45°with positive stops at 0°, 15°, 22.5°, 30°, and 45° in both directions. Comes with a laser that accurately tracks the real-time position and allows you to make precise adjustments.
  • 【2 Speed & Durable Tool】- With the single press of the switch, you can convert between two speeds(3200 RPM or 4500 RPM) with ease for more precise cutting, high speed for wood while low speed for metal. The sliding cutting design allows for cutting longer boards. Built from stainless steel castings, it provides you with a solid saw that is able to withstand the daily rigors that come with working on a job site.
  • These crown stops accurately position crown molding vertically against the saw fence.
  • Measures 6-1/2-x-4-1/2 inches.
  • Package include: 2 crown stops,one for each side of the blade, 2 screw knob, 2 nut clips.
  • Easy to adjust, strong and ridged. Replace for DEWALT DW7084.
  • These replacement Crown Stops are designed to fit for DeWalt miter saw DWS779 DWS780 DW703, DW706, DW708, DW712, DW715, DW716, DW717, DW718
  • Made in the USA
  • ZEROPLAY Miter Bars will fit ANY standard (3/4” x 3/8”) T-Track miter slot that measures between 0. 73" and 0. 79" wide and at least 5/16" deep
  • Top-down installation for easy and fast mounting to jigs, fixtures and sleds
  • No slop, side-to-side play or seasonal warping
  • Build table saw sleds fast
  • Compatible with: P450
  • Ryobi replacement assembly dust bag, part number 204443001
  • Genuine, OEM Ryobi Replacement Part
  • Please Note: Does not fit all specs of above models listed, please consult owner's manual for proper part number identification and proper installation
  • Compatible with: Specific P450 18v Brushless Belt Sanders
  • UNCONDITIONAL WARRANTY - LUVRD focuses on construction accessories, and we stand by our carpenter protractor, brings better alternatives for you in the miter saw protractor for woodworking. Welcome to find us with any product-related queries on buyer message
  • EASY TO USE - Owing to the adjustable and collapsible design, not only is this miter saw protractor angle finder easy to use, but also convenient to carry or store and feature a one-handed operation with a unique tightening mechanism
  • SUPERIOR QUALITY AND DURABILITY - This trig crown molding jig angle finder is durable and stronger than other pvc plastic miter angle gauge because it is made of high-quality ABS. Moreover, The miter saw protractor is resistant to scratch for daily use
  • FRIENDLY DESIGN - LUVRD professional miter saw protractor is not only an excellent replacement for 505p-7 miter saw protractor angle finder corner crown molding tool, but also a measuring rule in inches for construction
  • PRECISE MEASUREMENT - This miter saw protractor angle finder is specifically designed to ensure a correct and precise miter angle finder with no effort. The miter saw protractor could provide you the exact angle you need (inside or outside corners) to make your perfect trim for crown molding tool, baseboard molding and more
  • Opening measures: 13-Inch by 16-Inch
  • 4-Inch nominal end measures 3-31/32-Inch O.D. and 3-47/64-Inch I.D.
  • Tough, durable ABS plastic material
  • Outlet: 4-Inch for hose or pipe
  • Easy solution for catching sawdust

More Info

LKJYBG 450mm Miter Gauge, Miter Gauge Sawing Assembly Ruler, Universal Table Saw Miter Gauge with Track Stop Table Saw Router (Limit Only)

Search only LKJYBG brand name
LKJYBG 450mm Miter Gauge, Miter Gauge Sawing Assembly Ruler, Universal Table Saw Miter Gauge with Track Stop Table Saw Router (Limit Only)

Current price: 8.67 USD


Check price and availability


Weight: 0.249375 Pounds

  • Both ends of the fence are cut at exactly 45 degrees. This allows you to position the fence extra close to the saw blade (with the power turned off) so you have even more control over the workpiece you are cutting. The fence comes with a flip stop that makes repetitive cuts a breeze. When not in use the flip stop can be flipped up and out of the way. Also include are two sticky back measuring tapes. 1 tape is left to right reading and the other is right to left reading.
  • Made from a single piece of extruded aluminum, this precision miter gauge fence is not only durable, its accurate and saves setup time. The fence is designed to be used with most any miter gauge with its off-set mounting track on the back of the fence. The off-set track allows you to flip the fence for lower profile miter gauge mounts and flip back for standard height miter gauges. The fence can be mounted to older miter gauges by adding a wooden block mount with wooden screws if necessary.
  • The head is mounted to a solid steel miter bar that measure 18” in length and is .354” thick by .730” wide. Standard miter slots are 3/4” x 3/8” with a 1/8” “T” slot (slight variances from brand to brand) running the length on the bottom of the slot. The steel miter bar is equipped with a metal, removable retaining disc that measures 7/8” in diameter and is just shy of 1/8” to fit into to the “T” slot to prevent accidental lifting when feeding your stock through.
  • The .200” thick, adjustable, solid aluminum head is machined with 13 positive stop holes. 1 hole is at 90 degrees while the 6 holes on both sides are at 22.5, 30, 45, 60, 67.5 and 90 degrees. The positive stops are perfect for many woodworking projects as they are the angles that are typically used.To adjust the head you simply loosen the post knob handle, pull the spring loaded indexing pin outward, rotate the head to the desired position, release the pin and lock into place.
  • The Fulton Miter Gauge is a high quality, well thought out and economical solution for your table saw cross cutting needs.The Aluminum Miter fence is equally well thought out with its 45 degree ends for unsurpassed workpiece support and its ability to mounted to most any miter gauge. Also included is a handy aluminum flip stop for repetitive angled cuts on your table saw. Together these three items are the perfect compliment to each other for your table saw cutting needs.
  • Allow you to secure a wide variety of shop-made auxiliary fences to your existing fences without the Clamp getting in the way.
  • Range of travel 1/2″-5-3/4″ (12mm to 146mm)
  • Fits into a 3/8” hole in the top of the auxiliary fence
  • The steel miter bar is equipped with a metal, removable retaining disc that measures 7/8” in diameter and is just shy of 1/8” to fit into to the “T” slot to prevent accidental lifting when feeding your stock through. If your saw does not have a “T” slot, you can remove the disc. The steel miter bar is also equipped with spring loaded, adjustable plungers on the side of the bar. The plungers can be adjusted with the provide hex key wrench in or out to provide you with the ideal fit.
  • The head is mounted to a solid steel miter bar that measure 18” in length and is .354” thick by .730” wide. Standard miter slots are 3/4” x 3/8” with a 1/8” “T” slot (slight variances from brand to brand) running the length on the bottom of the slot. The steel miter bar is equipped with a metal, removable retaining disc that measures 7/8” in diameter and is just shy of 1/8” to fit into to the “T” slot to prevent accidental lifting when feeding your stock through.
  • To adjust the head you simply loosen the post knob handle, pull the spring loaded indexing pin outward, rotate the head to the desired position, release the pin and lock into place by tightening the post knob handle. The aluminum head has two ¼” x ½” slots milled into it for mounting a miter fence if so desired. The slots are approximately 1-1/8” from the base of the miter gauge head.
  • The .200” thick, adjustable, solid aluminum head is machined with 13 positive stop holes. 1 hole is at 90 degrees while the 6 holes on both sides are at 22.5, 30, 45, 60, 67.5 and 90 degrees. The positive stops are perfect for many woodworking projects as they are the angles that are typically used.
  • If you own a table saw and you need to make a crosscut at any angle then you know how valuable a miter gauge can be. You may also know that the miter gauge that came with your saw is not terribly accurate or durable. Not to mention that the fit in the miter slot may not be all that great as well. The Fulton Miter Gauge is a high quality, well thought out and economical solution to your table saw cross cutting needs.
  • 【Package Contents & 2-year Warranty】- advanced 10-inch 15-amp miter saw,1*10" multi-function blade, 2*10" blades for wood, 1* dust bag, 2*hexagonal wrench, 2* clamping device, 1*User Manual, 1*Warranty Card, 24 Months Warranty.
  • 【Clean Environment & Extension Table】- Additional chip bag connects directly to the saw,and helps to collect sawdust away from the workpiece during cutting. 35mm dust port allows you to connect your vacuum cleaner with an adapter instead of a bag to capture more of the dust. Extension table with vice clamping provides better support and balance, adding stability when cutting.
  • 【3 Blades & Iron Blade Guard】- Richer accessories provide a wide range of choices, two 10" 40T TCT blades for wood and plastic, and one multifunctional 10" 48T TCT blade for versatile use. Solid iron Self-retracting saw shield covers the teeth of the cutting blade, helps protect from accidental mishaps.
  • 【Bevel Cutting & Laser Guide】- A free bevel range from 0°to 45° allows you to make beveled cuts for more versatile uses. And the angle of the miter bench is -45°/0°/+45°with positive stops at 0°, 15°, 22.5°, 30°, and 45° in both directions. Comes with a laser that accurately tracks the real-time position and allows you to make precise adjustments.
  • 【2 Speed & Durable Tool】- With the single press of the switch, you can convert between two speeds(3200 RPM or 4500 RPM) with ease for more precise cutting, high speed for wood while low speed for metal. The sliding cutting design allows for cutting longer boards. Built from stainless steel castings, it provides you with a solid saw that is able to withstand the daily rigors that come with working on a job site.
  • These crown stops accurately position crown molding vertically against the saw fence.
  • Measures 6-1/2-x-4-1/2 inches.
  • Package include: 2 crown stops,one for each side of the blade, 2 screw knob, 2 nut clips.
  • Easy to adjust, strong and ridged. Replace for DEWALT DW7084.
  • These replacement Crown Stops are designed to fit for DeWalt miter saw DWS779 DWS780 DW703, DW706, DW708, DW712, DW715, DW716, DW717, DW718
  • Made in the USA
  • ZEROPLAY Miter Bars will fit ANY standard (3/4” x 3/8”) T-Track miter slot that measures between 0. 73" and 0. 79" wide and at least 5/16" deep
  • Top-down installation for easy and fast mounting to jigs, fixtures and sleds
  • No slop, side-to-side play or seasonal warping
  • Build table saw sleds fast
  • Compatible with: P450
  • Ryobi replacement assembly dust bag, part number 204443001
  • Genuine, OEM Ryobi Replacement Part
  • Please Note: Does not fit all specs of above models listed, please consult owner's manual for proper part number identification and proper installation
  • Compatible with: Specific P450 18v Brushless Belt Sanders
  • UNCONDITIONAL WARRANTY - LUVRD focuses on construction accessories, and we stand by our carpenter protractor, brings better alternatives for you in the miter saw protractor for woodworking. Welcome to find us with any product-related queries on buyer message
  • EASY TO USE - Owing to the adjustable and collapsible design, not only is this miter saw protractor angle finder easy to use, but also convenient to carry or store and feature a one-handed operation with a unique tightening mechanism
  • SUPERIOR QUALITY AND DURABILITY - This trig crown molding jig angle finder is durable and stronger than other pvc plastic miter angle gauge because it is made of high-quality ABS. Moreover, The miter saw protractor is resistant to scratch for daily use
  • FRIENDLY DESIGN - LUVRD professional miter saw protractor is not only an excellent replacement for 505p-7 miter saw protractor angle finder corner crown molding tool, but also a measuring rule in inches for construction
  • PRECISE MEASUREMENT - This miter saw protractor angle finder is specifically designed to ensure a correct and precise miter angle finder with no effort. The miter saw protractor could provide you the exact angle you need (inside or outside corners) to make your perfect trim for crown molding tool, baseboard molding and more
  • Opening measures: 13-Inch by 16-Inch
  • 4-Inch nominal end measures 3-31/32-Inch O.D. and 3-47/64-Inch I.D.
  • Tough, durable ABS plastic material
  • Outlet: 4-Inch for hose or pipe
  • Easy solution for catching sawdust
  • Widely Application: It can be used on most table saws and router tables with standard slots. Fit your table saw, band saw, router table, disk sander, or belt sander like a glove that has 3/8 x 3/4 inch slot.
  • Design: The positive stops are perfect for many woodworking projects as they are the angles that are typically used.To adjust the head you simply loosen the post knob handle, pull the spring loaded indexing pin outward, rotate the head to the desired position, release the pin and lock into place.
  • Precision: Angle guide with 27 total locking stops in 5 degree increments over a full 180-degree range, and allows for plus or minus 60-degree range miter cuts.
  • Feature: A lightweight design with a durable laser-cut aluminum construction, large gauge handle, universal fence mounting bracket, pivoting locking mechanism, a removal plate that allows the miter gauge to be used with T-slotted.
  • Premium Material: Made from a single piece of extruded aluminum, this precision miter gauge fence is not only durable, its accurate and saves setup time.

More Info

1    2    3    4    5    6    7    8    9    10